When a bilge pump stops working, the cause is usually one of four things: a float switch that's stuck or failed, no power reaching the pump (a blown fuse, a tripped breaker, a dead battery or a corroded connection), a clogged intake, or a worn-out pump motor. Flip the pump to manual first. If it runs on manual but not on its own, the float switch or the automatic circuit is the problem; if it won't run either way, trace the power from the battery to the pump.
That matters in Charleston, where boats sit in slips and on lifts through months of afternoon thunderstorms with only the automatic pump on watch. Here's how to find the fault and when to call a tech.
Safety comes before diagnosis. Put life jackets on everyone, start any manual or backup pump (or a bucket), and look for the source: a hose off a through-hull, a missing drain plug, a livewell line. If you can't keep up with the water, call the Coast Guard on VHF channel 16 and head for shallow water or the nearest dock. If you smell gasoline in the bilge, don't start testing switches or wiring; open the hatches, keep sparks away and get a professional to look at it.
Why is my bilge pump not turning on?
Work through it in this order with a flashlight and, ideally, a multimeter.
1. Try the manual switch
Most automatic setups have a manual position at the helm. If the pump runs on manual, the pump, its wiring and its power supply are fine, and the fault is in the float switch or its wiring. If it doesn't run on manual either, skip to step 3.
2. Check the float switch
Look at the float in the bilge. Hair, leaves, fishing line and sludge commonly jam it down. Clean around it and lift the float by hand: if the pump starts, debris was the problem. If nothing happens, the switch has likely failed. Float switches are wear items, and Practical Sailor lists bad float switches among the parts to replace before they fail. Its advice is to use switches that sit in a protective housing, since bare floats foul more easily.
Some pumps have a built-in water sensor instead of a float and only switch on at a set water level, so pour a few gallons in to test them.
3. Trace the power
If the pump won't run on manual or automatic, look for the break between the battery and the pump:
- Fuse or breaker: check the inline fuse near the battery and the breaker or fuse panel at the helm. A fuse that keeps blowing points to a jammed pump or a short.
- Battery: a flat battery means no pump. Boating Magazine notes that batteries going flat over the winter is one way a pump ends up useless. If yours drains between trips, see our guide to a boat battery that won't hold a charge.
- Connections in the bilge: this is where salt water does its damage. A crimp or butt splice that sits in bilge water turns green and stops passing current. Practical Sailor recommends long pump leads so the connections can be made up high, out of the wet bilge.
- The pump itself: if you measure 12 volts across the pump's positive and ground wires and it still won't run, the motor is done.
Why does my bilge pump run but not pump water?
If the motor hums but nothing comes out the side of the hull, check:
- A clogged intake or strainer. Pop the pump off its base and clean it.
- An airlock or a sagging discharge hose. Practical Sailor says the discharge line should rise steadily, because low spots trap air and stall the flow.
- Less capacity than you think. A pump's rated gallons per hour isn't what it delivers in your boat. Practical Sailor points out that some are rated at 13.6 volts rather than a more realistic 12.2, and every foot of lift and every bend in the hose cuts real output. A weak pump may simply be undersized.
Why does my bilge pump keep running or cycling on and off?
A pump that runs nonstop usually has a float stuck in the up position, or water is draining back into the bilge from the discharge hose. A pump that cycles every few minutes or hours is telling you water is getting in, and the pump isn't the real problem. Boating Magazine suggests fitting a bilge pump counter for exactly this reason: if the count jumps, find the new leak and fix it right away.
Common sources on Lowcountry boats:
- Rain. On an uncovered boat, a run of summer thunderstorms can keep the pump busy for days, and that alone can flatten a battery.
- Hoses and clamps below the waterline. Boating Magazine recommends one or even two quality stainless-steel clamps on hoses below the waterline, and replacing rusty ones.
- The stuffing box on inboards. Boating Magazine puts a normal drip at two or three drops a minute while running, and none at the dock with the engine off.
- Livewell and washdown plumbing, scuppers and cockpit drains.
- Sterndrive bellows. A torn bellows lets water in around the drive. Our sterndrive repair cost guide covers bellows replacement.
How should an automatic bilge pump be wired?
The automatic pump should keep working even when you've switched the boat off and gone home. Practical Sailor recommends wiring it straight to the battery through a fuse, not through the main battery switch, and notes that ABYC standards call for the fuse within 7 inches of the power source. It also recommends a readily accessible, clearly marked manual switch at the helm.
If the pump goes dead when you turn the battery switch off, have a marine electrician rewire it. Undersized or unfused wire on a jammed pump can overheat.
Do I need a second bilge pump or a high-water alarm?
For a boat that lives in the water, it's worth it. Practical Sailor recommends two pumps: a smaller one at the lowest point of the bilge for routine water, and a larger one mounted a few inches higher as a backup. It also recommends a high-water alarm loud enough for marina neighbors or staff to hear when the boat is docked.
That matters because most sinkings don't happen under way. Boating Magazine, citing BoatUS insurance claim studies, says more than two-thirds of recreational boat sinkings happen at the dock or on a mooring. In an older BoatUS claims study of outboard boats (reported by Soundings), rain was the leading cause of dockside sinkings, followed by leaking underwater fittings. A bilge pump removes nuisance water; it won't save a boat from a failed through-hull.
How often should I test my bilge pump?
Test it before every trip. It takes 30 seconds and it's on our pre-trip boat checklist. Once a year, do what Boating Magazine calls a stress test: run a hose into the bilge and confirm the pump and float switch kick on by themselves and push water overboard. If you're not on the boat often, have someone check it after big storms, especially during hurricane season, which runs through November 30.
Common questions
Can I fix a bilge pump float switch myself?
Often, yes. Cleaning debris away from a stuck float is a five-minute job. Replacing a failed switch is a basic wiring job with marine-grade heat-shrink connectors. Disconnect power first.
Should the bilge pump work with the battery switch off?
The automatic pump should. Practical Sailor recommends wiring it straight to the battery through a fuse so it keeps working when the boat is shut down. If yours goes dead when the battery switch is off, have the wiring changed.
Is a bilge pump enough to keep my boat from sinking?
No. A pump handles rain and small leaks. Most dockside sinkings start with water getting in through rain, fittings or hoses, so keep hoses and clamps in good shape, keep scuppers clear and check the boat after storms.
Need a mechanic?
If you can't trace the fault, the wiring is corroded or the pump keeps cycling and you can't find the leak, a technician can sort it out, often at your dock or lift. These DockWrench technicians list bilge and plumbing work on their profiles: Caine Robert (CWeed's Outboard Repair and Marine Services, mobile), Glenn Rubino (Eagle Marine Repair, mobile), Tony Caristi (Keep Er Wet Outdoors, mobile), Kyle Mikes (KJM Marine Services, mobile) and Harrison Miller (Miller's Marine of SC, marina shop). See marine electrical repair in Charleston for wiring work, or mobile boat mechanics who come to you. Not sure whom to call? Request a mechanic and describe the problem. It's free for boat owners.
Sources
- Practical Sailor: Bilge Pump Installation and Maintenance Tips
- Boating Magazine: 10 Ways to Prevent Your Boat From Sinking Dockside
- Soundings: Publication researches causes of sinkings (reporting a BoatUS Marine Insurance claims study)
Find a Charleston marine tech who lists bilge and plumbing work, including mobile techs who come to your dock. Free for boat owners.
Find a Marine Tech →